10G CWDM SFP+/XFP

10G CWDM SFP+/XFP transceiver modules are small form factor pluggable module for serial optical data communications. It is designed for single mode fiber and operates at a nominal wavelength of CWDM wavelength. There are 18 center wavelengths available from 1270 nm to 1610 nm, with each step 20 nm. A guaranteed minimum optical link budget of 14 dB is offered. Sopto supplies OEM service and Third-Party(Cisco, Juniper, HP, Dell etc.) compatible fiber optic transceivers.FeatureProduct Features● Single +3.3 V Power Supply● Built-in digital diagnostic functions● 2G/4G/8G/10G Fibre Channel compliance● Transmission distance up to 80km over SMF● Power Budget up to 10dB, 14dB, 16dB, 23 dB● Supports Multi Protocol 8.5Gb/s, 9.95Gb/s to 11.3Gb/s bit rates● Class 1 Laser International Safety Standard IEC-60825 Compliant● Uncooled 18-λ CWDM DFB/cooled EML LD: from 1270 nm to 1610 nm● Can be used with single fiber CWDM system or dual fiber CWDM system● Operating Case Temperature: Standard: 0~70°C; Extended: -20~85°C; Industrial: -40~85°CCompliant● RoHS-6● IEEE 802.3ae 10GBASE● SFF-8431, SFF-8432, SFF-8472Sopto fiber optic transceiver took the first lead to pass the ISO9001 quality system, the requirements of European CE, RoHsPin AssignmentDiagram of Host Board Connector Block Pin Numbers and Name.Pin Function DefinitionsPIN | Name | Function | Notes1 | VeeT | Module transmitter ground | Note 12 | Tx Fault | Module transmitter fault | Note 23 | Tx Disable | Transmitter Disable; Turns off transmitter laser output | Note 34 | SDL | 2 wire serial interface data input/output (SDA) |5 | SCL | 2 wire serial interface clock input (SCL) |6 | MOD-ABS | Module Absent, connect to VeeR or VeeT in the module | Note 27 | RS0 | Rate select0,optionally control SFP+ receiver. When high, input data rate>4.5Gb/ s;when low, input data rate <=4.5Gb/s |8 | LOS | Receiver Loss of Signal Indication | Note49 | RS1 | Rate select0,optionally control SFP+ transmitter. When high, input data rate >4.5Gb/s;when low, input data rate <=4.5Gb/s |10 | VeeR | Module receiver ground | Note 111 | VeeR | Module receiver ground | Note 112 | RD- | Receiver inverted data out put |13 | RD+ | Receiver non-inverted data out put |14 | VeeR | Module receiver ground | Note 115 | VccR | Module receiver 3.3V supply |16 | VccT | Module transmitter 3.3V supply |17 | VeeT | Module transmitter ground | Note 118 | TD+ | Transmitter inverted data out put |19 | TD- | Transmitter non-inverted data out put |20 | VeeT | Module transmitter ground | Note1Note 1. The module ground pins shall be isolated from the module case.2.This pin is an open collector/drain output pin and shall be pulled up with 4.7K-10Kohms to Host_Vcc on the host board.3.This pin shall be pulled up with 4.7K-10Kohms to VccT in the module.4.This pin is an open collector/drain output pin and shall be pulled up with 4.7K-10Kohms to Host_Vcc on the host board.SFP Module EEPROM Information and ManagementThe SFP modules implement the 2-wire serial communication protocol as defined in the SFP -8472.The serial ID information of the SFP modules and Digital Diagnostic Monitor parameters can be accessed through the I2C interface at address A0h and A2h. The memory is mapped in Table 1. Detailed ID information(A0h) is listed in Table 2. And the DDM specification at address A2h. For more details of the memory map and byte definitions, please refer to the SFF-8472, “Digital Diagnostic Monitoring Interface for Optical Transceivers”. The DDM parameters have been internally calibrated.Table 1. Digital Diagnostic Memory Map (Specific Data Field Descriptions)Table 2. EEPROM Serial ID Memory Contents (A0h)Data Address | Length (Byte) | Name of Length | Description and ContentsBase ID Fields | Base ID Fields | Base ID Fields | Base ID Fields0 | 1 | Identifier | Type of Serial transceiver (03h=SFP)1 | 1 | Reserved | Extended identifier of type serial transceiver (04h)2 | 1 | Connector | Code of optical connector type (07=LC)3-10 | 8 | Transceiver |11 | 1 | Encoding | NRZ(03h)12 | 1 | BR,Nominal | Nominal baud rate, unit of 100Mbps13-14 | 2 | Reserved | (0000h)15 | 1 | Length(9um) | Link length supported for 9/125um fiber, units of 100m16 | 1 | Length(50um) | Link length supported for 50/125um fiber, units of 10m17 | 1 | Length(62.5um) | Link length supported for 62.5/125um fiber, units of 10m18 | 1 | Length(Copper) | Link length supported for copper, units of meters19 | 1 | Reserved |20-35 | 16 | Vendor Name | SFP vendor name: SOPTO36 | 1 | Reserved |37-39 | 3 | Vendor OUI | SFP transceiver vendor OUI ID40-55 | 16 | Vendor PN | Part Number: (ASCII)56-59 | 4 | Vendor rev | Revision level for part number60-62 | 3 | Reserved |63 | 1 | CCID | Least significant byte of sum of data in address 0-62Extended ID Fields | Extended ID Fields | Extended ID Fields | Extended ID Fields64-65 | 2 | Option | Indicates which optical SFP signals are implemented(001Ah = LOS, TX_FAULT, TX_DISABLE all supported)66 | 1 | BR, max | Upper bit rate margin, units of %67 | 1 | BR, min | Lower bit rate margin, units of %68-83 | 16 | Vendor SN | Serial number (ASCII)84-91 | 8 | Date code | SOPTO’s Manufacturing date code92-94 | 3 | Reserved |95 | 1 | CCEX | Check code for the extended ID Fields (addresses 64 to 94)Vendor Specific ID Fields | Vendor Specific ID Fields | Vendor Specific ID Fields | Vendor Specific ID Fields96-127 | 32 | Readable | SOPTO specific date, read only128-255 | 128 | Reserved | Reserved for SFF-8079Recommended Host Board Power Supply CircuitRecommended High-speed Interface CircuitMechanical DimensionsAll optical transceivers are RoHS compliant and could be 100% compatible with branding equipment, such as Cisco, Extreme, Juniper, HP, H3C, Linksys, Huawei, Alcatel-Lucent, Foundry, Nortel, Force10 etc.If you want to know more about the exact information of the specified transceiver or get price, Please Contact Us>>.Applications● SONET OC-192 / SDH STM-64● OTN ITU-T G.709● 10GBASE-SR/LR/ER/ZR Ethernet● 10X/8X/4X/2X/1X Fibre Channel● CWDM NetworksRelated Articles● What is SFP-10G-LRM Optical Transceiver?● The difference of SFP 10G SR LR LRM ER and ZR● What is DDM Function for Fiber Optic Transceiver？● Fiber Optic Transceiver Module's Selection and Use SkillsOrdering InformationPN | Data Rate(Gbps) | Distance | Fiber | Output Power(dBm) | Sensitivity(dBm) | Interface | Temp. | DDMCWDM SFP+ | CWDM SFP+ | CWDM SFP+ | CWDM SFP+ | CWDM SFP+ | CWDM SFP+ | CWDM SFP+ | CWDM SFP+ | CWDM SFP+SPT-PC(27-61)TG-LR | 9.95~11.3 | 10km | SM | -4～0 | -14 | Duplex LC | 0-70℃ | DSPT-PC(27-33/47-61)TG-LRS | 9.95~11.3 | 20km | SM | -5～-1 | -17 | Duplex LC | 0-70℃ | DSPT-PC(21-33/47-61)TG-ER | 9.95~11.3 | 40km | SM | -1～3 | -17 | Duplex LC | 0-70℃ | DSPT-PC(47-61)TG-ZR | 9.95~11.3 | 80km | SM | 0～4 | -23 | Duplex LC | 0-70℃ | DCWDM XFP | CWDM XFP | CWDM XFP | CWDM XFP | CWDM XFP | CWDM XFP | CWDM XFP | CWDM XFP | CWDM XFPSPT-XC(27-61)TG-LR | 9.95~11.3 | 10km | SM | -4～0 | -14 | Duplex LC | 0-70℃ | DSPT-XC(27-33/47-61)TG-LRS | 9.95~11.3 | 20km | SM | -5～-1 | -17 | Duplex LC | 0-70℃ | DSPT-XC(21-33/47-61)TG-ER | 9.95~11.3 | 40km | SM | -1～3 | -17 | Duplex LC | 0-70℃ | DSPT-XC(47-61)TG-ZR | 9.95~11.3 | 80km | SM | 0～4 | -23 | Duplex LC | 0-70℃ | D